Securing and Qualifying Single-Use Technologies - The authors suggest techniques for mitigating risk and securing the supply chain for single-use components used in biopharmaceutical manufacturing. -


Securing and Qualifying Single-Use Technologies
The authors suggest techniques for mitigating risk and securing the supply chain for single-use components used in biopharmaceutical manufacturing.

BioPharm International Supplements
Volume 26, Issue 4, pp. s18-s23


Once the single-use supply chain has been established, it is crucial to assess what qualification activities are needed to implement a single-use system. While it is common knowledge that leachable-and-extractables testing is a necessary part of a single-use component program, it's important to realize that leachable-and-extractables testing can be costly to perform. However, testing may be reduced depending on the overall risk to the product for each single-use item. According to Destry M. Sillivan of FDA, manufacturers should "submit sufficient information to provide evidence that the product contacting material does not introduce contaminants into the product so as to alter the safety, identity, strength, etc." (5). If there is little to no relevant risk associated with the material in question, "vendor data can be cross referenced and a detailed justification for the applicability of these data and a justification for no additional testing should be submitted" (5).

Risk assessment

When assessing what qualification activities are needed for single-use component implementation, it is important to identify the product contact components that may present a higher leachable and extractable risk. A risk assessment is a valuable tool to determine what the crucial single-use materials are in a process. Those that surpass the tolerable amount of risk for an organization may then be slated for acquiring additional vendor information and further in-house testing. Multiple factors should be considered as part of the risk assessment including the nature of final product, how the process stream contacts the single-use component, the single-use component material properties, and the attributes of the process solvents. Once appropriate risk factors have been identified, a risk assessment should then be used to determine the extent of the qualification required for each component. Tools for performing a risk assessment as well as the general risk-based philosophy are outlined in ICH, Q9 Quality Risk Management (6).

It is important to recognize that a single-use item is often composed of many component parts that may or may not be made out of the same materials. Vendor documentation should be closely inspected to determine the material of construction of each component. Not all of these component parts may be manufactured at the vendor's facility. A primary reason for this is that many vendors outsource different components that comprise their single-use assemblies. Accordingly, subvendors must be contacted to obtain their validation packages for the individual parts to complete the risk assessment.

Figure 3: Single-use storage bag example risk assessment.
Consider, for example, a single-use bag system; there are the bag films, the connectors, the tubing, the capsule filters, and sampling connections as shown in Figure 3. As noted above, each of these items may be made out of different materials that all need to be considered for potential risk to product.

This example of a risk assessment performed on a storage bag illustrates how different components of a single-use bag can have different risk scores. The storage bag itself is rated at a higher risk relative to the rest of the component parts because it has a larger surface-area-to-volume ratio and the film is in contact with the storage material for an extended period of time. Where this bag is used in the production process will determine the overall outcome of the risk assessment. If the storage bag was used in upstream process the risk is low; however, if the storage bag was used in late stages of the process it becomes a much higher risk and would require leachable testing.

What the drug product is intended to treat, the intended route of administration, and where the single-use item is used within the process stream are the leading risk factors. The longer the product is in contact with the single-use item, the greater the risk that leachables will be transferred into the process stream. When considering this risk factor, it is important to recognize that the tubing on a component part may only see the process stream for a fraction of the time that a bag may see. This and the varying materials of construction are the reasons that component parts of each assembly should be considered separately. The proximity of the single-use item to final fill will increase the risk because there is less opportunity for the leachable (or particulate) to be mechanically or chemically removed via filtration or chromatography. The volume of product stream when compared with the surface area of the single-use item is also an important risk factor because the lower the volume is, the more potentially leaching surface area that it may contact. Consider the product contact area of a ultrafiltration/diafiltration (UF/DF) filter; the exceptionally high surface area as well as its proximity to the end of the process makes it a much higher risk to the product than an upstream storage bag.

blog comments powered by Disqus



Suppliers Seek to Boost Single-Use Technology
August 21, 2014
Bristol-Myers Squibb and Celgene Collaborate on Immunotherapy and Chemotherapy Combination Regimen
August 20, 2014
USP Center in Ghana Receives International Lab Accreditation
August 15, 2014
USP Awards Analytical Research
August 15, 2014
FDA Warns about Fraudulent Ebola Treatments
August 15, 2014
Author Guidelines
Source: BioPharm International Supplements,
Click here